Laser Tube Engraver

RECI 100W W2 CO2 Glass Laser Tube Water Cooling for Engraving 100W Laser Machine

RECI 100W W2 CO2 Glass Laser Tube Water Cooling for Engraving 100W Laser Machine
RECI 100W W2 CO2 Glass Laser Tube Water Cooling for Engraving 100W Laser Machine
RECI 100W W2 CO2 Glass Laser Tube Water Cooling for Engraving 100W Laser Machine
RECI 100W W2 CO2 Glass Laser Tube Water Cooling for Engraving 100W Laser Machine
RECI 100W W2 CO2 Glass Laser Tube Water Cooling for Engraving 100W Laser Machine

RECI 100W W2 CO2 Glass Laser Tube Water Cooling for Engraving 100W Laser Machine

RECI 100W W2 CO2 Glass Laser Tube Water Cooling for Engraving 100W Laser Machine. Reci W2 100W CO2 Laser Tube Wooden Box Packing Length 1200mm Dia.

80mm CO2 For Laser Engraving Cutting Machine. Mark & Model: W2, The product is featured as small size and good model, higher power rate compared with the laser tube of similar length and longer service time, which is suitable for laser marking, laser cutting and laser engraving.

Make sure to follow the operation instruction of model W2 as shown in the illustration. The dedicated power P12 should be equipped.

The positive pole of laser tube is in high voltage (the ignition voltage is 19kv). It may cause the following consequence when it is failed to follow the instruction: Arcing; the inner tube will be punctured by electricity and may cause water leakage.

Water cooling: using purified water; 2 to 5 liter/minute; water temperature: 10? The operating environment: temperature 2-40? The working current: test current is 29mA.

Maximum working current is 29mA. The running current must be kept below 27mA. The life span can reach 8,000 hours if the current is kept below 25mA. The ammeter must be connected to the negative electrode of laser tube.

When it is working under over-high current for long term, the negative pole will appear light yellow and the life span will be shortened rapidly. To protect dust from going into the insulation sheath, please wrap it with plastic film. When the working current is 4mA and the tube is in the state of preionization, the laser can be used for high-frequency impulse engraving.

Do not clean the exterior surface of the output widow mirror with tools such as tampon; otherwise the output power will be seriously affected. The followings are the designated methods to clean up pollution in the exterior surface of window mirror.

1 When the mirror is polluted, do not turn on the laser. 2 Blow the mirror surface sideways with an air blower.

3 Spray the pure alcohol on the mirror surface with sprayer. 4 Turn on the laser after the alcohol gets fully volatilized. 5 If the methods above don't work effectively, it is necessary to ask for the professional to use tampon with alcohol to clean the mirror surface from middle to edge.

The best solution is to prevent the window from being polluted. Attention: it is forbidden to clean the mirror with acetone. The screws in the front and back ends of the laser tube are not allowed to be moved, otherwise the output power will be declined, even the tube will be scrapped.

Put the acryl 300mm far away from output mirror, when testing its laser spot. The laser beam is invisible light. Please wear protective glasses when debugging the laser. The positive pole is in high voltage.

Pay attention to the security marks. Pour out cooling fluid in the event of storage and transportation, and cover the output terminal with a dust-proof plastic bag. The storage environment is 2-40? And the requested humidity is 10-60%.

Pack the laser as in the original way. Important notes: it is requested to use adhesive tape to cement the sponge together with laser tube to prevent the tube from vertically sliding during transportation.

The sponge in the side of output mirror must be 70 mm beyond it, and the sponge in the side of reflecting mirror must be 50 mm wider. I will sent you the item by TNT/DHL Express, we will provide Wooden Case Packing. We will make our efforts to help you solve the problem. All items will be dispatched within 2-3 days.

We recommend that you leave us with your physical address. We will reply you ASAP. Please do NOT leave negative or neutral feedback without asking for help. We aim to provide Top Level Customer Service, we will try our best to solve any problem. Your satisfaction is our first priority. We will take care of the cost to send the replacement item to you. Special circumstances will be listed clearly in the listing. Please do check everything carefully after you received the parcel. This item is in the category "Business & Industrial\Printing & Graphic Arts\Screen & Specialty Printing\Engraving". The seller is "chinacnczone-de" and is located in this country: CN. This item can be shipped worldwide.
  • Brand: Reci
  • Model: Reic W2
  • Material: glass
  • Features: CO2 Laser Tube
  • Length: 1200mm
  • Usage: CO2 Laser Engraving Cutting Machine
  • Max Power: 100W
  • Diameter: 80mm
  • Bundle Listing: NO

RECI 100W W2 CO2 Glass Laser Tube Water Cooling for Engraving 100W Laser Machine